Solid Wood
- Solid wood is a natural material that displays unique variations in grain and colour.
- Exposure to light can cause its colour and character to change over time.
- Being a living material, wood responds to its environment - it may dry out and contract in warm, dry air, while high humidity can cause it to expand.
- These natural properties give solid wood its distinct beauty, and with proper care, you can help extend its lifespan significantly.
General Care
- For daily maintenance, simply wipe down the solid wood with a clean, well-wrung damp cloth.
- If any stains or dirt accumulate, use a mild soap solution or a gentle wood cleaner.
- Be sure to follow up with a dry cloth to remove any excess moisture.
- Keep the wood away from direct sunlight to prevent discolouration.
- and avoid placing it near strong heat sources like fireplaces or radiators, as extreme heat can lead to warping.
- It’s also best to cover the surface with breathable materials during long periods of inactivity, and maintain a room humidity level between 40% and 60%.
Oiled solid wood
- This product comes with an oil-treated surface, but regular oiling every 10-12 months is recommended to maintain its natural beauty.
- Use a neutral wood oil, applying it in the direction of the grain with a soft sponge or lint-free cloth.
- Allow the oil to dry for three hours, then wipe away any excess to keep the surface smooth and protected.
- You can also use a white-pigmented oil or stained (darker colour) oil, but please be aware that once any of these oils has been applied, you cannot go back to the original colour again, so choose wisely.
When applying wood oil, it's important to note that it can slightly alter the color of the wood due to its natural properties. This change can enhance the wood’s grain and provide a richer appearance, but it may also darken or otherwise modify the original hue. It's always a good idea to test the oil on a small, inconspicuous area first to see how the wood will react before applying it to the entire item.
For stubborn stains, such as red wine or grease, gently rub the area with a soft cleaning sponge moistened with some wood cleaner. You may need to repeat this treatment a couple of times, leaving a few days between each session to allow the wood to breathe. Once the stain is removed, sand the area with 220-grit sandpaper. If the stain has penetrated deeper into the wood, begin by sanding with 180-grit sandpaper, and then finish with 220-grit sandpaper. When sanding with rougher grit (e.g., 180-grit), it’s important to sand over a wider area to avoid creating a dip in the wood.
Once the area is sanded, treat the entire piece with an oil treatment to restore the surface. Keep in mind that the sanded area may appear lighter after oil treatment, but this will even out over time as the wood is exposed to light. For the most even results we recommend sanding and oil treatment of the entire surface.
For tougher stains or areas with wax build-up, carefully remove any excess wax with a sharp object, taking care not to scratch the wood. Afterwards, you can try removing any remaining stain with petrol or solvent (be cautious of fire hazards – use in a well-ventilated area and in small quantities). Once the stain has been removed, follow the same steps as for other stains by sanding the area and then applying an oil treatment.
To eliminate minor scratches, begin by sanding with 180-grit sandpaper, always sanding along the grain of the wood. Then, follow up with 220-grit sandpaper to smooth the surface. After sanding, treat the entire surface with oil to restore the finish.
For pressure marks or deeper scratches, most can be removed if the wood fibres haven’t broken. First, brush the mark with lukewarm water to help the wood fibers expand. After the wood dries, sand it with 220-grit sandpaper. If the pressure mark is more pronounced, you can carefully steam the wood. Dampen a tea towel with clean water, fold it, and place it over the mark. Then, press a very hot iron on top of the towel (without touching the wood directly). The steam will help the wood expand. Afterwards, dry the area and sand with 220-grit sandpaper before applying an oil treatment.
We recommend testing any oil treatment on a concealed area first to ensure compatibility before applying it to visible surfaces.
As solid wood is a natural material, it will expand and contract with changes in temperature and humidity. Small cracks or splits may appear, but don’t worry - these are normal.
Tables
To prevent scratches, avoid placing or dragging sharp or coarse objects across the tables surface. We recommend to always use placemats or coasters to protect the tabletop. Wipe away any spills immediately.
To maintain your tabletop's durability and appearance, we recommend oiling the top surface every 10-12 months and treating the underside every third application. Only the top surface should be sanded, as sanding the underside is not necessary. This routine keeps the wood well-conditioned and protected.
Please use a pad for your laptop and do not place it directly on the solid wood surface, as the extreme heat from the ventilator can cause local cracks on the wood.
When moving, please lift your furniture and do not push or drag furniture across the floor.
Fittings and screws should be checked once a year.